您所在的位置:首页 > Information dynamics  > Drilling information
福州钻井机故障与维修常识!
source :www. 释放time :2020age 10月13time
  钻井机它在水利建设中得到了广泛的应用、Ground temperature drilling equipment for farmland engineering。不管是什么设备,,Need to be maintained and maintained,只有提高工作效率,Extend the starting life,为了提高工作效率,Extend the starting life,What are the common failures of drilling platforms??如何好好干维修工作,降低钻床故障率??
  

钻井机


  钻床常见故障及排除方法
  
  Fault one
  
  钻井油泵启动后,钻井油泵不上油或油量不足,First, check that the fuel in the tank is insufficient or oil-free,If you don't rule out refueling to the oil level line,,Check to see if the filter is clogged,其他,我还需要看看水箱里的通风口是不是堵塞了,Or a loose entrance to a suction pipe joint, etc.;
  
  故障two
  
  钻机油泵的热磨损,修理和更换泵,这种油的粘度太高或太低,油应严格按照指示启动;At the same time, check the transmission device of the oil pump of the drilling machine.,提高装配精度;
  
  Fault three
  
  钻床耦合加热,弹性环的过度磨损;原因是当钻床的动力机器与离合器装配在一起时,,,Coaxial difference,需要提高装配同轴度;
  
  Fault four
  
  钻机提升机的锁紧与打滑,主要原因是制动带内部存在油污,锁的内表面需要拆卸;If the brake of the drilling machine is free of oil,,检查制动带与制动轮之间的间隙,If you're too loose,,You should adjust it properly.;
  
  失败五
  
  High temperature problem of hydraulic Oil for drilling Machine,Too little oil in the tank or damage to the oil pump,Refueling or repairing oil pump;工作泵的合理选择,Recommended work pressure according to instructions。
  
  two 、Repair and maintenance method of drilling Machine
  
  1、工作时应注意冲击器的声音和变速箱的操作,应立即停止不正常的声音和现象,及时检查;
  
  2、时刻注意航道和输气管道的检查,钻各种配件用螺栓、坚果 无论它是否强大?;
  
  3、当工作面浸入水中时,大直径钻头开口,Insert drill pipe,把钻杆带到水面上1-2M ,防止泥浆和矿渣掉进洞里;
  
  4、当钻床在短time 内停止工作时,A small amount of pressure should be put on,Prevent sediment from invading the impact device of drilling machine,如果钻停了很长time ,,冲击器应从洞底提起1-2Fixed at the meter;
  
  5、Drilling machine is not allowed to reverse when drilling,以防钻杆掉进洞里;
  
  6、加新钻杆时,注意保持洞的清洁,Impactor to prevent sediment from mixing into the drilling machine,钻床部件损坏;
  
  7、每节课结束时,,工程钻机表面的污垢应及时清除,除正常操作外,严禁工作面拆卸;
  
  8、The tension of the crawler plate should be checked regularly,不要太松或太紧(人8),长time 灭活,Reptiles should relax.。
  
  8、Pay attention to checking the lubricating oil condition of the motor at any time;
  
  9、Butter Lubrication of drill Pipe Joint and Reducer of drilling Machine。
  
  10、车体上的所有连接螺栓、螺丝 、坚果 ,Do this before and after each class,进行详细检查,And strengthen the loosening part.;
  
  11、万一下雨下雪,机械设备应及时进行防水防潮处理;If it's deactivated for a long time,,应该存放在仓库里,好好干:防潮、Antioxidant work、防火、Anticorrosion。
  
  If you want the drill to work well,,,Time and constant maintenance is essential;
  
  Must be checked before starting,Regular maintenance cannot be reduced。
  
  开机前看看油,Cooling water level needs to be high enough;
  
  The air filter cannot be clogged,如,The fuel wouldn't be on the scene.。
  
  钢丝喇叭,别忽视它,液压油计;
  
  钻头齿尖需要检查,Don't forget the separation of oil and water。
  
  它必须持续一百个小时,Found all the pin shafts of the cylindrical rod.;
  
  加油周转箱,High impurity removal effect of fuel tank。
  
  200滤芯更换小时,Valve clearance to ensure;
  
  每周500小时,需要记住定期维护:
  
  500Head gearbox oil,未来,它将有一千小时的路程,靠;
  
  各种过滤元件都需要移除和更换,齿轮润滑也很重要。
  
  Supercharger needs to be checked1000小时,所有固件都被考虑在内;
  
  Motor belt cannot be loosened,更换岩心,Change the oil to clean it。
  
  四千小时很重要,High pump inspection efficiency;
  
  如果钻井平台要放假,,别忘了擦干它;
  
  Careful maintenance,商业财富攀升至新高。

有关规定